|
Mackie 406M 500-Watt RMS/2-Ohm Mono Powered Mixer Powered Mixers for Professionals The PPM Series 406M features: 500 real watts/2 ohms from twin 250-watt FR Series High-Current power amps Power amps switchable as mains or main plus monitor 6 mic/line channels with master phantom power Inserts on all 6 channels Active 3-band EQ on each channel 2 separate 9-band, audiophile-quality graphic EQs-- one on mains and one on monitor All PPM Series Powered Mixers feature: Rugged injection-molded chassis resists impacts that would destroy a rat-fur-covered wood box powered mixer. Built-in handle can be used by folks who don't have the foggiest idea of what injection molding is. A real Mackie mic/line mixer section! Based on our world-famous MicroSeries 1202-VLZ and enhanced with new mic preamps and about a gazillion ingenious extra features. Rugged, sealed rotary controls resist dust, moisture and other contamination. Expensive, studio-grade, 9-band program equalizers for mains and monitor that utilize multiple summing amplifiers and precision infinite feedback band-pass filters, which yield superior linear-phase and combining properties. What this means is our graphic EQs are exceptionally low-noise, low-distortion, sound great, and don't suffer from any nasty phase-shift problems. Level-setting control & LED on every PPM mixer channel-makes setting input levels a snap. Mil-spec fiberglass circuit boards (instead of cheap phenolic) resist physical impact. Amp routing switch assigns power amps to mains or mains + monitors. Hefty 10,000 f storage capacitors for high peak power reserves. Massive toroid transformer for high current output. PPM Series heat sink Mega-cool die-cast heat sink. 1-piece die-cast heat sink is custom-cast for maximum heat dissipation and minimum car upholstery destruction. Black coating improves efficiency by 15%. Running Man figure improves coolness-factor by 150%. Specification: Frequency Response Mic Input to Main Mixer Output (Trim at 0 dB) +0, -1 dB 32Hz to 20kHz +0, -3 dB 16Hz to 80kHz Mic Input to Power Amp Output at rated power output: +0, -1 dB 32Hz to 20kHz +0, -3 dB 16Hz to 55kHz Distortion: THD and SMPTE IMD; 20 Hz to 20 kHz Mic Input to Main Mixer Output Mic Input to Power Amp Output Common Mode Rejection Ratio: (CMRR) at 1kHz, Trim at 0 dB 60 dB Noise: 20Hz-20kHz bandwidth, 150-ohm source impedence Equivalent Input Noise (EIN): -127 dBu Residual Output Noise with Main Mixer, Monitor, & Effects outputs, Channel & Master levels off: -95 dBu Main Mixer Output Noise with Master at nominal (-10dB), all channels off: -92 dBu with Master and one input at nominal (-10dB and -20dB), Trim at 0dB: -85 dBu Crosstalk, at 1 kiloHertz: Adjacent Inputs or Input to Output: -90 dB Fader Off: -90 dB Break Switch Mute: -80 dB Input Level Trim Control Range: 0 to -40dB Phantom Power: +15V DC Equalization: Rumble Reduction 75hz, -18dB/octave Channel EQ High 15dB at 12kHz Mid 12dB at 2.5kHz Low 15dB at 80Hz Graphic EQ: 9 bands, 15dB, Q=1.414 ISO octave centers at 63Hz, 125Hz, 250Hz, 500Hz, 1kHz, 2kHz, 4kHz, 8kHz, 16KHz Main Mixer Section Rated Output: Main Mixer, Monitor, and Effects +4 dBu Maximum Main Mixer Section Output +20 dBu Input Sensitivity (Minimum Input Level to produce +4dBu at Main Mixer Output) Mic Input: -68dBu Insert Input: -28dBu Line Input: -48dBu Stereo Line Input: -28dBu Tape Input: -18dBu Effects Return: -18dBu Maximum Voltage Gain: Mic Input to… Insert Output: 40dB Tape Output: 60dB Main Mixer Output: 72dB Line Input (Mono) to… Insert Output: 20dB Tape Output: 20dB Main Mixer Output: 52dB Stereo Line Input to… Tape Output: 20dB Main Mixer Output: 32dB Tape Input to… Tape Output: 10dB Main Mixer Output: 22dB Effects Return to… Main Mixer Output: 22dB Monitor Output: 22dB Input Impedance: Mic Input balanced 3 kilohms Insert Input unbalanced 10 kilohms Line Input balanced 40 kilohms Stereo Line Input unbalanced 10 kilohms Tape Input unbalanced 10 kilohms Effects Return unbalanced 10 kilohms Power Amp In unbalanced 10 kilohms Output Impedance Main Mixer Output 150 ohms Insert Output 150 ohms Tape Output 150 ohms Monitor Output 150 ohms Effects Send 150 ohms Power Amp Out 0.032 ohms at 1kHz Digital Effects: Resolution 32-bit EMAC internal processing, 2-channel Sample Rate 31.25 kHz Bandwidth 15.6 kHz VU Meters: Main and Monitor, eight segments Clip, +5, 0, -5, -10, -15, -20, -30 Maximum Power at 1% THD, midband (both channels driven) 2 ohms: 250W x 250W per channel 4 ohms: 200W x 200W per channel 8 ohms: 125W x 125W per channel 2 ohms: 500W total Continuous Sine Wave Average Output Power, 40Hz to 20kHz (both channels driven at rated power) 180W per channel: 4 ohms, no more than 0.15% THD 110W per channel: 8 ohms, no more than 0.10% THD Power Bandwidth: <10Hz to 30kHz (+0, -1dB) at rated power into 4 ohms Frequency Response <10Hz to 30kHz (+0, -1dB) <10Hz to 55kHz (+0, -3dB) Distortion (THD, SMPTE IMD): 4 ohms: <0.15% 8 ohms: <0.10% Signal-to-Noise Ratio: <105dB below rated power into 8 ohms Channel Separation: >75dB at1 kHz Damping Factor: >250dB at1 kHz Amp Input Impedance: 10k ohms unbalanced, 20k ohms balanced Continuous Sine Wave Average Output Power (both channels driven at rated power into 4 ohms): 1.35V (+4.8dBu) Gain (amp in to speaker out): 26.4dB(21V/V) Maximum Input Level: 9.75V (+22dBu) Rise Time: < 5 s Slew Rate: > 40V/ s Load Angle: 8 ohms, time independent: 8 (±jx) 4 ohms, time dependent: 4 (±jx) High Frequency Overload and Latching: No latch up at any frequency or level High Frequency Stability: Unconditionally stable driving any reactive or capacitive load Physical: Height: 11.7 inches (297mm) Width: 20.5 inches (521mm) Overall Depth: 13 inches (330mm) Weight: 32 lbs (14.5 kg)
|
